If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Flip and send us a picture of the wheel face Reg, I'd fit these until they get trashed then have a change...
The face is unpainted and looks ok (from 10 yards) as it is with a bit of orange peeping through the holes - I cant be bothered messing about and will just blow the faces in solid orange.
I will fit them until something else comes along, hopefully they wont get trashed as by that time the scene will have caught up with the cheesemeister and I'll be able to flog them to sausages for 'big dolla' as I believe the hip cats say nowadays.
The carpet lasted a few days before I admitted to making a hideous mistake and ripped it out - I stashed it in the loft thinking it may come in handy but I couldn't even face using it in the garage.
I'm chuffed with the intercooler though, subtle and works well.
Injectors rebuilt
Only received four of the five nozzles I ordered
Waiting for my pop tester to turn up now.
Hi reg what make nozzles did you use just about to order some topran ones
Agreed Sausages. "Cool" - it's a peak too high when you're in such good 'styling' company... I'm positive the Cheese Meister has only put up that alternative build to demonstrate that he's got form when it comes to style!
Found them on Facebook, freshly made from used wheels, £200 delivered, width of my choice, done by Damian Force. I normally swear by Alonze but the quality of these are equal to Jim's work.
Found them on Facebook, freshly made from used wheels, £200 delivered, width of my choice, done by Damian Force. I normally swear by Alonze but the quality of these are equal to Jim's work.
He did mine , top job , only thing I will say is there's slight bit or rusting on rim lips , I think might be chips
Gibontas because they are supposed to be the best. Never heard of Topran nozzles.
I've a contact that builds injectors for cheaper than you can buy the nozzles, he is probably using snide Bosch nozzles made from pure chinesesuim that may or may not be rubbish depending on what you read/believe.
I must be missing a spanner here, but putting 15" bsnded rims on a T4 is like fitting wheels to an avacado!
Nah - he's bang on with 15s - they look right with enough drop, 19"/20"s and the max power 90s are long gone, euro is where it's at....or was 10 years ago, it's all about OEM+ now - I'll give him a few years to get there, the scene kid is new but at least he's keen.
Anyway.....
Wheels are now on hold, clutch is on it's way out and a de-map is going in for the time being.
Still.... I've got these bad boys
Even though my kids have disowned me, said I've gone full blown gay and refuse to go in the van - which is a bonus as it'll take the load off the clutch.
Last edited by regcheeseman; 26 January 2018, 11:38 PM.
I've a contact that builds injectors for cheaper than you can buy the nozzles, he is probably using snide Bosch nozzles made from pure chinesesuim that may or may not be rubbish depending on what you read/believe.
I've been sourcing nozzles, just testing a few sets of 0.26 & 0.28 but for modified vans.
You know my thoughts on standard nozzles - they're good enough for 200bhp.
Reg will - I'm sure- confirm his current Stanadynes are performing?!
Still.... I've got these bad boys
Even though my kids have disowned me, said I've gone full blown gay and refuse to go in the van - which is a bonus as it'll take the load off the clutch.
..... " I've gone full blown gay," so you were nearly there before fitting these retina burners,.... sod the clutch how about issuing cheap shades or a daylight curfew?
Comment