If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Not sure if the O2B diff crownwheel is larger and the diff axis is further away from input shaft axis - that would sit the CV cups further back towards the bulkhead.
It's the webbed section over and above the output cup that might cause interference problems with the subframe - hard to tell, it could be ground back but that is far from ideal.
O2N six speed
T4 standard O2B
At least the O2N has a speed sensor - which is a bonus over the O2Q
What were the ratios of the FPE compared to the O2B - I wasn't sure about the figures I found for the FPE, cant remember what the o2B ratios are?
Last edited by regcheeseman; 2 October 2019, 09:47 PM.
Not sure if the O2B diff crownwheel is larger and the diff axis is further away from input shaft axis - that would sit the CV cups further back towards the bulkhead.
It's the webbed section over and above the output cup that might cause interference problems with the subframe - hard to tell, it could be ground back but that is far from ideal.
O2N six speed
[ATTACH=CONFIG]13836[/ATTACH]
[ATTACH=CONFIG]13838[/ATTACH]
T4 standard O2B
[ATTACH=CONFIG]13837[/ATTACH]
At least the O2N has a speed sensor - which is a bonus over the O2Q
What were the ratios of the FPE compared to the O2B - I wasn't sure about the figures I found for the FPE, cant remember what the o2B ratios are?
Yeh I spotted the speed sensor port on ETKA. Although it might be in an awkward position if that top/side diff casing could be the issue?
Agreed I'm sure I've read the same that the crown wheel is beefed up on the 02B but I'll x-ref the internals shortly.
Do you know your vans gearbox code? Mine's EWB which could be miles apart from yours! I'll post up the ratios.
I have a wheel speed at 60mph - I know that needs to multiply by about 4 to get engine revs
But I cannot work out what combo of ratios i need to do to get four - obvs it need to be top gear and final drive but that is 4.235 and 0.7 for the 02B and how do they make 4?
Why are there two final drive ratios for the FPE?
1st and second tall ratios I like - maybe the thing will accelerate from standstill rather than just rev and go nowhere?
4th and 5th are very close - then a massive jump to 6th
It's got two shafts 1st to 4th gear, then 5th & 6th on the second shaft.
aha - that makes the 4-5 ratios make sense but unfortunately means that 1 - 4 are no less useful than I hoped they might be - and it buggers my table up.
Would you email your table so I can play with it?
Out numbers dont tally though - you get 164mph at 5000 rpm in 6th - I make it 131 - different tyres but it should only be a couple of % at most?
Last edited by regcheeseman; 2 October 2019, 11:34 PM.
Dave Sausages has got one - cheers for the offer though.
Cleared out the back of the van - the self-adhesive acoustic foam that initially didn't seem to stick very well - had stuck like the proverbial after 3 years.
The metal frame is a mock-up of the seat base.
Sizing up the seat mounts, trying to space them suitably to support the base effectively
It took about an hour or so of staring, measuring, checking under the van, before I decided where the rails should go. I wanted to follow one ridge in the floor from front to back but some do not flow front to back. There's also a pair of chassis members running front to back, they are quite wide and enclosed meaning you cannot fit nuts on the underside; a large area of floor is not suitable for attaching rails.
Eventually I settled on suitable positions, and then aligned the positions of the rails using the square frame to space off the cab step.
Holes drilled for the front mounts and the bolts dropped through
Comment