Page 7 of 7 FirstFirst ... 567
Results 61 to 68 of 68
  1. #61
    Activ8's Avatar Moderator
    Join Date
    Oct 2017
    Location
    Derbyshire
    Posts
    10,508
    Thanks
    4,006
    Thanked 3,418 Times in 2,698 Posts

    Quote Originally Posted by qtronix View Post
    just thought i would put it here for people looking for a cheap pump upgrade,
    i was given an fuel pump off a Kia Sedona 2.9 its a 11mm pump with lda 20mm shaft. the boost pin looks like the modded ones you can buy with steep ramp angle.
    0460414139 VE4/11F2000R624-3
    didn't even think of looking into thses cars for pumps lol.
    Great find qtronix, 11mm pumphead too, I'm assuming it's not a sraight swap on a 1.9?

  2. #62
    qtronix's Avatar Now you're learning (Copper)
    Join Date
    May 2019
    Posts
    67
    Thanks
    8
    Thanked 66 Times in 38 Posts
    Quote Originally Posted by Activ8 View Post
    Great find qtronix, 11mm pumphead too, I'm assuming it's not a sraight swap on a 1.9?
    yeah 11mm pump head.

    didn't have a pulley on so dont no the count. it has a timing advance is off the fuel pump pressure line so you would have to swap it out but apart from that its a stright swap.

  3. The Following User Says Thank You to qtronix For This Useful Post:

    Activ8 (27th July 2019)

  4. #63
    qtronix's Avatar Now you're learning (Copper)
    Join Date
    May 2019
    Posts
    67
    Thanks
    8
    Thanked 66 Times in 38 Posts
    should have put it has an electronic cold start that is on the fuel pressure regulator to the timing advance. its only a 12v supply like the start solenoid. so you could use that and do away with the manual pull handle or swap it out. but to swap it out the would have to swap the advance plunger as it has no cam bar and to do that the pump has to come apart.

    just searched for the engine name KIA 2.9TD 16V SEDONA CARNIVAL J3 KJ ENGINE DIESEL FUEL PUMP
    Last edited by qtronix; 27th July 2019 at 11:29 PM.

  5. The Following User Says Thank You to qtronix For This Useful Post:

    Activ8 (28th July 2019)

  6. #64
    qtronix's Avatar Now you're learning (Copper)
    Join Date
    May 2019
    Posts
    67
    Thanks
    8
    Thanked 66 Times in 38 Posts
    after my tig welder broke a couple of years ago i have finally got around to getting another one. picking it up friday a nice ac dc tig. so i can weld a manifold up for this and new weater tank. sould be fun

  7. The Following 2 Users Say Thank You to qtronix For This Useful Post:

    AndyLeach (31st July 2019),Fruitbat (31st July 2019)

  8. #65
    qtronix's Avatar Now you're learning (Copper)
    Join Date
    May 2019
    Posts
    67
    Thanks
    8
    Thanked 66 Times in 38 Posts
    pixked up my tig the other day so i can start to make the new manifolds and inlet the ones i have now are steel and look a bit ****
    Click image for larger version. 

Name:	IMG_20190803_124604.jpg 
Views:	51 
Size:	88.4 KB 
ID:	13251

  9. The Following 3 Users Say Thank You to qtronix For This Useful Post:

    Activ8 (3rd August 2019),damont4 (3rd August 2019),Fruitbat (3rd August 2019)

  10. #66
    qtronix's Avatar Now you're learning (Copper)
    Join Date
    May 2019
    Posts
    67
    Thanks
    8
    Thanked 66 Times in 38 Posts
    things have come to a stop once again lol, just as you have things planned out bills and shit come in that put things back (again).
    picking up the gas for the welder this friday and there charging me 20 quid to pick it up nice.
    moded the inline pump for the oil return, had a mate flow test it on his bench.
    now this is where things might change.
    i might just run the gt35 and inline. i had the supercharger fixed in my head but i am aiming for a higher number now.
    the block is coming back out to have liners put in and iam in talks with a guy about a griddle for it.
    the oil pump shaft is coming out and a idle pulley is going to be made for it so a dry sump can be fitted.

  11. The Following 2 Users Say Thank You to qtronix For This Useful Post:

    Activ8 (14th August 2019),AndyLeach (14th August 2019)

  12. #67
    regcheeseman's Avatar Privileged
    Join Date
    Jan 2016
    Location
    North Devon
    Posts
    3,649
    Thanks
    73
    Thanked 1,831 Times in 1,158 Posts
    Quote Originally Posted by qtronix View Post
    iam in talks with a guy about a griddle for it.
    I used to make and produce block girdles back in the day, sold a fair few, mainly to the GTD forum

    Google 'regcheeseman girdle block' gets you

    Click image for larger version. 

Name:	girdle003.jpg 
Views:	28 
Size:	63.1 KB 
ID:	13381

    I still have the CAD files - could get you a price for a 1 off, probably be £50, you'd need to get spacers turned, but I've got the CAD files for those as well, you need 10 off spacers at around £3 a pop. less if you have a mate with

    Have a look here http://vwdiesel.net/forum/index.php?topic=27133.0
    Last edited by regcheeseman; 14th August 2019 at 01:15 PM.

  13. The Following User Says Thank You to regcheeseman For This Useful Post:

    AndyLeach (14th August 2019)

  14. #68
    AndyLeach's Avatar Unemployed (Platinum)
    Join Date
    Sep 2018
    Location
    Swansea
    Posts
    1,747
    Thanks
    3,889
    Thanked 746 Times in 535 Posts
    This talk is completely over my head but Iím watching with so much interest 🤙🏽


    T4ism is not a Dis-easeJust T4s

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •